Chromatography Tubing
Hach Company Tubing, Tygon, E-3603, 3.2 mm (I.D.)
Chemical-resistant, Formula E-3603 Tygon tubing with flex strength greater than rubber. Unaffected by oxidizing agents and compatible with virtually any laboratory chemical. Bends readily to sharp radius curves and will maintain strong grip on glass or metal. Highly polished bore prevents interior build-up while facilitating cleaning.
Trajan Scientific PEEK Tubing, Natural PEEK Tubing - 360 µm OD x .006" ID x 100FT, 3500 PSI
PEEK Tubing, Natural PEEK Tubing - 360 µm OD x .006" ID x 100FT, 3500 PSI. PEEK tubing has the strength required to withstand continuous use at HPLC pressure without swelling or bursting, and is not affected by halide salts, high strength buffers, or other aggressive mobile phases that corrode stainless steel. The polymer surface will not leach metal ions into the eluent or extract metal-sensitive components from the sample. Note however that dichloromethane, THF, and DMSO may cause swelling in PEEK, and concentrated nitric and sulphuric acid will attack PEEK.
Shimadzu Scientific Instruments MarvelXACT Stainless Steel 125um ID X 600mm Tubing w/Fittings
MarvelXACT is comprised of flexible 1/32" OD stainless steel tubing for easy routing through the LC system and can be connected and disconnected multiple times. The 1/16" tubing ends and integrated fittings are compatible with any 10-32 coned port, and are finger-tight — no tool required for UHPLC connections up to 19,000 psi. The fitting produces a haptic "click" feedback when it reaches the optimum torque to eliminate the risk of under- or over-tightening. The PEEK tubing end seals at the port bottom which eliminates dead volume and minimizes carryover risk, peak tailing, and peak broadening. Tubing volume: 7.363uL.
Perkin Elmer US LLC Stainless Steel ATD Prepacked Sample Tubes, Sorbent: Tenax™ TA60/80 Pkg 10
The Tenax TA is conditioned at 320 °C. PerkinElmer recommends a maximum temperature of 350 °C for this sample tube with a desorption temperature of 300 °C. The tubes approximate analyte volatility range is n-C7 to n-C26 and the typical analytes for the Tenax TA are aromatics except benzene, apolar compounds (BP>100 °C) and less volatile compounds.
Trajan Scientific Tubing PEEKSil Beige Medical 2/PK
1/16 OD x 0 05 mm ID x 550 mm length PEEKsil tubing beige PK2
Trajan Scientific Tubing PEEKSil Beige Medical 2/PK
1/16 OD x 0 53 mm ID x 500 mm length PEEKsil tubing beige PK2
Microsolv Technology Corporation Tubing, PEEK, 0.005" ID, 1/16" OD, Super-T Grade, Red Stripes. 25 Meter Roll. 1 EA.
This Super-T™ grade ( Premium ), PEEK tubing is extruded from virgin PEEK ( Victrex ) material without adding any additives. The broken red stripes are added only to the outside of the tubing, leaving the interior all natural PEEK which eliminates leachables due to color. The internal and outer dimensional tolerances of this tubing is +/- 0.025mm. Color Code: Red, Stripes for 0.005" ( 0.13mm ) ID. Pressure rating: 6100 psi.
Microsolv Technology Corporation Tubing, FEP, 0.010" ID, 1/16" OD, Low Pressure. 5 Meter Roll. 1 EA.
This MicroSolv FEP ( Flourethylene Propylene ) low pressure tubing is chosen for use in Ion Chromatography Applications, but can be used in all low-pressure, laboratory applications including before and after an HPLC Pump such as with Mobile Phase Delivery and Solvent Waste Systems. Also known as Teflon FEP.Do not use this tubing with heat over 80⁰C. Internal and Outer Dimensional Tolerance: +/- 0.10mm Color: Natural FEP, Translucent ID: 0.010" (0.25 mm ) Pressure rating: 1650 psi.
Waters Corporation Tubing Assembly, Capillary, With Frit, 40 μm, 16 in.
This capillary tubing with frit is designed for use with the 10,000psi nanoACQUITY system. It connects from the nano tee to the trap valve tube, supporting various system configurations for optimized performance.
- Designed for 10,000psi nanoACQUITY systems.
- Connects nano tee to the trap valve tube.
- Supports direct injection configurations.
- Supports 2D with dilution configurations.
- Supports single pump trapping configurations.
- Supports vented dual pump trapping configurations.
- Includes integrated frit.
Waters Corporation Tubing Assembly, Capillary, Injector to Trap Valve, 40 μm × 13 in.
This capillary tubing fits between the injector and the trap valve of the nanoACQUITY UPLC with dual pumps. It is used in the Vented Dual Pump and Dual Pump Trapping configurations. The tubing measures 40μm by 13 in. long.
- Designed for nanoACQUITY UPLC systems with dual pumps
- Ensures reliable connection between injector and trap valve